INSTALL NEW FEEDER AND 125 AMP SUBPANEL TO POWER RECEPTACLE OUTLETS AND THE SUBPANEL BENEATH THE POOL. INSTALL NEW FEEDER AND 40 AMP SUBPANEL TO POWER THE LIGHTING AROUND THE DECK AND THE POOL. INSTALL LIGHTING, SWITCHES AND RECEPTACLE OUTLETS.
INSTALL 3 DEDICATED BRANCH CIRCUITS: ONE FOR THE DECK RECEPTACLES, ONE FOR THE EMERGENCY CIRCUIT FOR THE LIGHTING AND ONE TO FEED THE EMERGENCY CIRCUIT FOR LIGHT SAFETY. PROPER BONDING OF POOL AND DECK AREA. ALL WORK TO BE DONE ACCORDING TO THE 2017 NEC AND PER PLANS.City of Philadelphia · 2025
NEW JUICE MACHINE CIRCUIT
1. Supply and Install (1) LE Grand Model 2097TRAPLW GFI receptacle fed from a dedicated 20A circuit
2. Supply all wiring, conduit, MC Cable, New Circuit and outlet requested by Sam’s Club for install
3. Repair and sand any holes or cut outs in drywall if needed or required.
4. Clean all debris form the site and dispose of all trash, left over materials, tools, and remove from site.
5. Provide photos of work performed, before, during and after completion of outlet installation
6. Provide photo of voltage reading of outlet tested after installation to show outlet reads correct voltage
7. Obtain managers signature after completed work, with a fully printed name and signature
Not included in Work:
Sub-Panel Installation
Runs longer than 150 Feet
NOTE
No surface mounting is able to be performed. All electrical wiring is to be ran from the ceiling tile down, so you should not have to cut into the drywall completely. Feeding the wiring into an existing conduit run if there is room.
Runs should be no more than 150 feet from the panel. If they are, then we can request more funds for longer stretches to the panel.
There should be enough space in the panel for a new circuit. All sites require the wiring to be ran on a dedicated circuit.
If there is no space in the panel for a new circuit, we will quote for a subpanel to be installed.
Store to provide lift upon availability for the tech to use while running the new wiring to the designated location.City of Philadelphia · 2025
INSTALL 100 AMP FEEDER FROM MAIN PANEL TO THIRD FLOOR. INSTALL 100 AMP SUBPANEL FOR THE INSTALLATION OF THE 100 FEEDER. REWIRE HOUSE THROUGHOUT AND INSTALL LIGHTING, SWITCHES AND RECEPTACLE OUTLETS. INSTALL INTERCONNECTED SMOKE AND CO ALARMS WITH 10 YRS BATTERY ACCORDING TO THE 2017 NEC.
This profile was built from public permit records. Claim it free to add your photo, phone, and website, so the homeowners landing here can actually reach you.
EV Charger (Installation Only)
- Supply and install 2-pole 60 Amp branch circuit breaker in existing main panel.
- Supply and install 60A/240V dedicated circuit using copper conductors from main panel to exterior rear wall of home.
Run 6/2 armored cable along basement surface and convert to PVC conduit on exterior of house.
Circuit to be concealed in PVC conduit where exposed on the side and rear of home.
- Mount EV charger on exterior rear wall of converted garage near driveway.
- Terminate all wiring within main electrical panel and EV charger.
- Energize and test charging station and identify circuit in main panel.
TYPE II SURGE SUPRESSION
- Supply and install Leviton single-phase, 120/240 volt NEMA-1 Surge Protection Devices, one for each main breaker panel.
- Supply a dedicated 240 volt, 20 amp circuit mounted at the top of the buss.
- Energize and test.
PANEL MAINTENANCE AND CLEANING
- Blow out panel debris.
- Clean off all contacts.
- Ensure all connections are tight.
- Inspect and test arc fault circuit breakers (AFCI)
- Inspect and test ground fault circuit breakers (GFCI)
- Note and report any deficiencies.
Electrical Permit
- All Phase to apply for township permit and coordinate inspection via third party electrical underwriter.City of Philadelphia · 2025
MAIN SERVICE
- Disconnect taps from PECO aerial.
- Supply and install mount and strap to reconnect PECO aerial to house.
- Supply and install new service head.
- Supply and install hardware to properly secure service cable.
- Supply and install antioxidant at terminals in meter socket.
- Complete termination of service cable to PECO aerial.
- Energize and test.City of Philadelphia · 2024
REWIRE APARTMENT THROUGHOUT. INSTALL LIGHTING, SWITCHES AND RECEPTACLES OUTLETS. INSTALL 120 VOLTS INTERCONNECTED SMOKE/CO ALARMS. RELOCATE SUB PANELS AND REPLACE FIRE ALARM DEVICES ACCORDING TO THE 2017 NEC AND PER PLANS.City of Philadelphia · 2024
E2.0 Lighting Plan
-Supply wiring to and install fixture A 4' LED strip light. (14)
-Supply wiring to and install fixture B 6" round edgelit down light. (35)
-Supply wiring to and install fixture X LED exit light with battery backup. (5)
-Supply wiring to and install fixture EM dual headed emergency light. (6)
-Install wiring, box, and device for single pole switch. (2)
-Install wiring, box, and device for 3-way switch. (4)
-Install wiring, box, and device for motion sensors ( 2 ceiling & 1 wall) (3)
E3.0 Power Plan
- Install wiring, box and device HP-17 dedicated 120V/20A circuit feeding (4) duplex convenience receptacle.
- Install wiring, box and device HP-19 dedicated 120V/20A circuit feeding (4) duplex convenience receptacle.
-Install wiring, box and device HP-21 dedicated 120V/20A circuit feeding (4) duplex convenience receptacle.
-Install wiring, box and device HP-23/25 dedicated 240V/30A circuit feeding (1) exterior condensing unit with service disconnect.
-Install wiring, box and device HP-27 dedicated 120V/20A circuit feeding AHU-1 with service disconnect.
- Install wiring, box and device HP-29 dedicated 120V/20A circuit feeding new lighting.
-Install wiring, box and device HP-20/22 dedicated 240V/20A circuit feeding HP-1 with service disconnect.
-Install wiring, box and device HP-24/26 dedicated 240V/20A circuit feeding EUH-1 with service disconnect.
-Install wiring, box and device HP-28 dedicated 120V/20A circuit feeding MOD-1. ALL WORK IS TO BE DONE ACCORDING TO APPROVED DRAWINGS-2017 NEC.
**FIRE ALARM IS ON A SEPARATE PERMIT**City of Philadelphia · 2024
MAIN SERVICE
- Shut down power at panel and remove meter.
- Disconnect taps from PECO and remove service cable and meter socket.
- Remove fuse panels and load-side service cable from meter to panel.
- Supply and install new 100 Amp service cable and PVC weather head.
- Supply and install a 100 Amp aerial fed meter socket with weather-proof hub.
- Supply and install new painted backboard.
- Supply and install a 100 amp, 20 space/40 circuit main breaker load center.
- Supply all required bonding and grounding of new service.
- Extend circuits to new panel where required.
- Supply and install all required branch circuit breakers and complete all terminations.
- Identify circuits and place panel schedule.
- Prepare a drip leg and make insulated splice connection to PECO feeders.
- Re-install meter into socket, energize and test circuits.
- Supply and install box and tamperproof GFI receptacle next to panel.
BEDROOM
- Fish wire to location below to add a dual function receptacle to protect wiring as per code.
- Fish wiring to center room location. Pull up floor boards in attic to run wire.
- Supply fan rated box and install standard customer supplied ceiling fanCity of Philadelphia · 2024
-Install (2) LED recessed lights to match the existing and controlled by existing switch. (4-week lead time on fixtures) DEN / STUDY
- Install all wiring, box, and device for (2) tamper resistant convenience receptacles along desktop.
- Install low voltage, LED, under cabinet lighting with extrusion and lens mounted along bottom of shelving above desk.
- Install 4", 10 watt, ultra-thin, LED recessed light and drive to illuminate shelves from ceiling.
- Remove and replace existing switch with new preset, system dimmer as specified.
LAUNDRY
- install (2) 4", 10 watt, ultra-thin, LED recessed light and driver to illuminate appliances from ceiling. HALL CLOSETS (2)
- Install low voltage door contacts to control new linear LED fixture mounted above the door for single door and double door closets.
PANTRY
- Install low voltage door contacts to control the new linear LED fixture mounted above the door.
DINING ROOM
- Complete assembly and installation of customer supplied ceiling fixture utilizing existing fixture box and wiring. - Remove and replace existing switch with new preset, system dimmer as specified.
KITCHEN
- Complete assembly and installation of customer supplied ceiling fixture utilizing existing fixture box and wiring. - Remove and replace existing switch with new preset, system dimmer as specified.
MASTER BEDROOM
- Complete assembly and installation of customer supplied ceiling fixture utilizing existing fixture box and wiring. - Remove and replace existing switch with new preset, system dimmer as specified.
FOYER
-Install (5) new Lumenture linear, LED, recessed, adjustable fixture. (3 along the accent wall and 2 along the short wall at the entrance)
- Install single pole dimmer location to control new recessed fixtures.
LIVING ROOM
- Install Juno, 2-circuit, line voltage track lighting to parallel length and width of room as specified.
- Anchor track to concrete ceiling and penetrate pantry wall to access wiring.
- Install (12) trackCity of Philadelphia · 2024
DEMO
- Electrical demo due to renovation and refeed existing circuits to remain. (Allowance)
UNIT 10E - BEDROOM
- Supply and install 4", 10 watt, ultra thin, LED recessed light and driver.
- Wiring to and installation of standard customer supplied ceiling fan.
- Install all wiring, box, device and plate for single pole switch.
- Install all wiring and device for tamper resistant convenience receptacle and cover plate.
GALLERY
- Supply and install 4", 10 watt, ultra thin, LED recessed light and driver.
- Supply and install 4", 10 watt, ultra thin, LED Wall Wash recessed light and driver.
- Supply and install (2) Lutron Caseta main dimmer switch and (1) PICO remote dimmer switch.
- Install all wiring and device for tamper resistant convenience receptacle and cover plate.
WALK-IN-CLOSET
- Supply and install LED closet light.
- Install all wiring, box, device and plate for occupancy sensor switch.
HALL
- Remove and replace existing recessed light with 4", 10 watt, ultra thin, LED recessed light and driver.
- Supply and install (1) Lutron Caseta main dimmer switch and (1) PICO remote dimmer switch.
FOYER
- Remove and replace existing recessed light with 4", 10 watt, ultra thin, LED recessed light and driver.
- Supply and install (3) Lutron Caseta main dimmer switch and (1) PICO remote dimmer switch.
KITCHEN
- Remove and replace existing recessed light with 4", 10 watt, ultra thin, LED recessed light and driver.
LIVING ROOM/DINING ROOM
- Remove existing low volt recessed light and wiring.
- Remove and relocate all wiring, box, and existing chandelier fixture to location specified.
- Remove all wiring and existing mono-point recessed light fixture.
- Remove and relocate all wiring and existing mono-point recessed lights to locations specified.
- Supply and install 4", 10 watt, ultra thin, LED recessed light and driver.
- Troubleshoot and repair existing LED accent lighting.
(Billed at time and material and added to total costs)City of Philadelphia · 2023
SIGN WIRING
- Disconnect power to existing sign to accommodate replacement by sign contractor.
- Reroute/extend existing wiring to new sign after installation and complete terminations.
NOTE
- Sign removal and installation not included and by others.
- Quote is based on existing wiring being in good working order.
- Quote is based on two trips being required.
- Energizing, testing, and programming of sign by sign company.
ELECTRICAL PERMIT & INSPECTION
- Supply City electrical permit and underwriter's inspection.
- Permit is for electrical work being completed and not sign replacement.
As per 2017 necCity of Philadelphia · 2023
Electrical Permit for combo CP-2023-001089City of Philadelphia · 2023
Permitted projects on public record. Addresses are omitted for privacy.